Softeners and Whole House Systems

How to Test Your Water Hardness at Home

Test your water hardness with a utility report, test strip, liquid kit or lab test. See which methods are reliable and how to read the results.

On this page
  1. Start with your utility’s water quality report
  2. Test strips
  3. Liquid titration kits
  4. Certified lab tests
  5. The soap test
  6. Tests that do not measure hardness
  7. Converting units
  8. Reading your result
  9. Well water: test more than hardness
  10. Frequently asked questions

The quickest way to learn your water hardness is your utility’s water quality report, if it lists hardness. For a home reading, a liquid kit is more precise than a test strip. For decisions about a softener, or for a private well, a certified lab is the reference. This guide explains each method, how to read the results, and why a few popular home tests do not measure hardness at all.

Short answer: Start with your utility’s report or a certified lab if you can. Use a liquid kit or a good test strip for a quick home reading. Treat the soap test as a rough screen, and skip vinegar tests.

Start with your utility’s water quality report

Community water systems must publish an annual Consumer Confidence Report (CCR). Not every report lists hardness, but many do, especially where mineral levels are high. Look for “hardness” in the table of detected substances, which is often given in mg/L as calcium carbonate. Your utility’s website usually has the latest report.

Test strips

Dip a strip in a glass of tap water for the time listed on the package, then compare the colors on the strip with the chart. Strips are quick and cheap and give an approximate range. They are useful for a rough check, but they are not precise enough for sizing a softener. Read the color in good light, and use the same brand each time you retest.

Liquid titration kits

A liquid kit adds a reagent a drop at a time until the water changes color, and the number of drops gives the hardness reading. These kits are more precise than strips and cost a little more. Read the instructions to confirm that the kit measures hardness, since some kits only check general water quality.

Certified lab tests

A certified lab gives the most reliable result, and it can test for other things at the same time. Your state health department or county extension office can point you to certified labs in your area. The EPA also publishes a list of labs certified by state. For a private well, a lab test is the reference, and you should test for more than hardness.

The soap test

Fill a clear bottle about one-third full with tap water, add about 10 drops of liquid soap, put the cap on, and shake for about 10 seconds. Clear, foamy water suggests softer water. Cloudy water with little foam suggests harder water. It is a rough screen, not a measurement, so use it only to decide whether a proper test is worth doing.

Tests that do not measure hardness

Some seller guides suggest a vinegar test, where fizzing shows how hard the water is. That is not a hardness test. Vinegar reacts with solid carbonate deposits such as scale, not with the calcium and magnesium dissolved in clear water, so the fizz does not tell you how hard the water is. Skip it.

Converting units

  • 1 grain per gallon (gpg) = 17.1 mg/L, which is the same as 17.1 ppm, of hardness as calcium carbonate.
  • To convert mg/L to gpg, divide by 17.1.
  • For reference, 60 mg/L is about 3.5 gpg, 120 mg/L is about 7 gpg, and 180 mg/L is about 10.5 gpg.

Reading your result

Using the USGS scale:

  • Soft: up to 60 mg/L (about 3.5 gpg)
  • Moderately hard: 61 to 120 mg/L (about 3.5 to 7 gpg)
  • Hard: 121 to 180 mg/L (about 7 to 10.5 gpg)
  • Very hard: above 180 mg/L (over 10.5 gpg)

A single reading can change with the season and the source, so retest before a major purchase.

Well water: test more than hardness

If you have a private well, the water is your responsibility. Hardness alone does not tell you whether the water is safe. Many health departments recommend at least annual testing for bacteria and nitrate, and additional tests for iron, manganese, and pH if you see stains, odors, or a change in taste. Ask your local health department which tests it recommends for your area. Is softened water safe to drink? covers the sodium question that follows from a softener.

Frequently asked questions

Can I test hardness without a kit?

You can get a rough sense from the soap test or from your utility’s report. Neither gives a number you can size a softener with. For a purchase decision, use a kit or a lab.

Can I use Dawn to test for hard water?

You can run the soap test with dish soap such as Dawn. It is a rough screen and will not give a measured hardness.

How often should I test?

Test once before you size or buy a system, and again if you notice changes or if your utility changes its source. Well owners should follow the testing schedule their health department recommends.

The complete guide to softeners and whole house systems

Whole House Water Softeners and Conditioning Systems Reviewed
Read the guide

Keep exploring

Guides from other topics

All topics →