Short answer
Shock chlorination means adding a high concentration of chlorine to a well, pump, pressure tank and plumbing, letting it sit, then flushing it out. It is a one-time disinfection step, used after a positive bacteria test, after well repairs, or to deal with sulfur or iron bacteria. It does not fix the cause of contamination, and it should be followed by a lab test.
The exact amount of bleach depends on your well’s depth, casing diameter, pressure tank and plumbing. Use a dosing chart from your state extension service or a licensed well contractor. Do not rely on a rule of thumb.
When to shock a well
- A lab test found total coliform or E. coli.
- The well or pump was repaired, opened or serviced.
- The well was flooded or had surface water enter it.
- Sulfur or iron bacteria are causing odor or staining.
Shock chlorination is not a substitute for routine testing. If the water keeps testing positive after treatment, the well may need repair, sealing or a new source.
Safety first
- Turn off the pump power at the breaker before you remove the well cap.
- Wear gloves and eye protection, and old clothes you do not mind staining.
- Never mix bleach with other cleaners, especially ammonia or acids. The mixture releases toxic gas.
- Keep children and pets away from the work area and from the water during the contact time.
- Work outdoors where you can, and keep the area ventilated.
Choose the right bleach
Use plain, unscented liquid laundry bleach that contains about 5 to 6 percent sodium hypochlorite. Read the label, because scented, splashless or color-safe formulas may contain other ingredients. Bleach loses strength over time, so use a fresh bottle.
Work out the dose from a chart
Extension guides provide dosing tables based on the standing water in your well and the volume of the plumbing and pressure tank. The standing water volume depends on the depth of the water column and the casing diameter. Read the chart carefully, and check the target chlorine concentration it gives.
Bypass treatment equipment
High chlorine levels can damage softeners, carbon filters, UV lamps, reverse osmosis membranes and water heaters. Before you start, turn off or bypass these units, following the manufacturer’s instructions. Reinstall them after flushing.
Add the chlorine to the well
- Measure the bleach from your chart.
- Mix it into a bucket of clean water first. A diluted solution is gentler on metal parts and the pitless adapter.
- Remove the well cap. Use a funnel or a clean hose or pipe to pour the mixture past the pitless adapter and down the casing, so it reaches the water below.
- Connect a garden hose to an outdoor tap, and run water into the top of the casing for 10 to 15 minutes. This washes the chlorine down the sides and mixes it through the water.
- Replace the cap securely.
Circulate through the plumbing
- Turn the pump power back on.
- Open each indoor and outdoor tap, shower and hose bib one at a time. Run cold water until you smell chlorine, then run the hot water too, so chlorinated water reaches the water heater.
- Remove faucet aerators and screens first, so loosened rust and debris do not clog them.
- Keep going until chlorine odor is clear at every outlet.
Let it sit
Leave the solution in the well and plumbing for the contact time your extension guide gives. Many guides suggest 12 to 24 hours. Do not drink, bathe or use the water during this time. Set up an alternative supply of drinking water for the household and pets.
Flush the system
- Flush outdoors first. Run a hose away from lawns, plants, streams and septic systems until the strong chlorine smell fades. Check local rules on discharge.
- Flush indoors. Open cold and hot taps until the bleach smell is gone. Reinstall aerators.
- Restore equipment. Turn treatment units back on and reinstall clean filter cartridges.
Retest the water
Wait until the system has been flushed and the chlorine smell is gone. Then collect a sample for a certified laboratory to test for total coliform and E. coli. Many guides suggest waiting about one to two weeks before taking the sample, so the result is not affected by residual chlorine or by the time it takes for bacteria to return. Do not drink the water until the lab confirms it is safe.
If the test is still positive, call a licensed well contractor or the health department. The well may need inspection, repair or a different disinfection method.
For what to do about the water before and after this process, see how do I know if my bore water is safe to drink. For the wider treatment options, including disinfection after filtering, see how to filter well and bore water for drinking.