Well Water

How to Get Rid of Rotten Egg Smell in Well Water

Rotten egg smell in well water often means hydrogen sulfide. Learn how to find the source and choose a fix, from water heater care to whole-house filters.

On this page
  1. Short answer
  2. Find where the smell starts
  3. Safety in enclosed spaces
  4. Fix a water heater problem
  5. Fix a well-level problem
  6. Choose a treatment system
  7. Keep the water tasting right

Short answer

A rotten egg smell in water usually comes from hydrogen sulfide gas, which may be dissolved in the groundwater or produced by sulfur bacteria in the well, pipes, softener or water heater. Find out where the smell starts before you buy a filter. The fix depends on the source. Water heater problems are cheap to fix. Well-level problems usually need a treatment system or a well inspection.

Find where the smell starts

Run each tap and note when the smell appears:

  • Hot water only. The problem is most likely the water heater. Sulfate-reducing bacteria in the tank can react with a magnesium anode rod to produce hydrogen sulfide.
  • Hot and cold water, from every tap. The source is probably the well or the groundwater itself.
  • Softened water only. Sulfur bacteria may be growing in the water softener.
  • Strongest when water first runs, then fading. Sulfur bacteria in the well or plumbing are likely.
  • Constant and unchanged with use. Hydrogen sulfide is probably dissolved in the groundwater.

A lab test for hydrogen sulfide, bacteria and iron tells you more. Ask for the sulfide level, not just a yes or no.

Safety in enclosed spaces

Hydrogen sulfide is a hazardous gas in enclosed spaces. Well pits, basements and small rooms can build up dangerous levels. Ventilate the area before entering. Do not work in a poorly ventilated well pit alone. If you smell a strong odor in one of these spaces, leave and call a professional.

Fix a water heater problem

  • Replace the anode rod. Many heaters use a magnesium anode that can react with sulfate in the water. Some guides suggest an aluminum or zinc anode instead. Check the warranty and manufacturer guidance before changing it.
  • Flush and disinfect the tank. A chlorine bleach solution, used according to the manufacturer’s directions, can kill sulfur bacteria inside the tank. Follow the flushing steps for your heater.
  • Raise the temperature with care. Some guides suggest setting the heater to a high temperature for several hours to kill bacteria. This risks scalding and uses more energy, so consult the manufacturer and take the safety steps they advise.

Fix a well-level problem

  • Shock chlorination can clear sulfur bacteria from the well, pump, pressure tank and plumbing. It is a temporary fix if the bacteria return quickly. For the process, see how to shock chlorinate a well.
  • Clean the well casing if the bacteria have built up on it. A well contractor should do this.
  • Test again after treatment, and keep testing on a schedule.

If you also have iron bacteria, which form slimy deposits, a specialist may be needed. See iron filters for well water.

Choose a treatment system

Systems differ in how well they handle different levels of hydrogen sulfide. A lab result for sulfide helps you pick the right one.

  • Activated carbon works for low levels, mainly for taste and odor. It is used up over time and needs regular replacement.
  • Oxidizing filters use air injection, catalytic media or manganese greensand to convert dissolved sulfide into solid sulfur, then filter it out. Manganese greensand needs regeneration with potassium permanganate.
  • Oxidation and filtration systems feed chlorine or hydrogen peroxide into the line, give the water time in a retention tank, then filter the solids. These suit higher levels.
  • Aeration removes the gas by mixing air into the water. It may need an additional filter to catch the solids that form. It works best at low to moderate levels.

Ask a dealer to match the system to your sulfide level and iron content. The dealer should base the choice on a lab test, not on the strength of the smell.

Keep the water tasting right

  • Keep carbon and media on schedule, because spent media can release odors.
  • Retest after any change to the treatment.
  • Watch for the smell returning, because it can signal bacteria in the softener or water heater.

For the full treatment order, including sediment and disinfection, see how to filter well and bore water for drinking. For the cost of different treatment systems, see well water filtration system cost.

The complete guide to well water

How to Filter Well and Bore Water for Drinking
Read the guide

Keep exploring

Guides from other topics

All topics →