Under-Sink and Countertop Systems

How to Install the Brondell Three-Stage Water Filtration System

Step-by-step guide to installing a Brondell three-stage under-sink carbon filter, covering tools, shutoff, connections, flushing, and leak checks.

On this page
  1. What you need before you start
  2. Step 1: Shut off the water and check the space
  3. Step 2: Mount the filter head or bracket
  4. Step 3: Connect the cold supply
  5. Step 4: Connect the tubing and faucet
  6. Step 5: Flush the filters
  7. Step 6: Check for leaks
  8. Common problems and fixes
  9. Finding replacement filters
  10. What the certifications mean for this system

What you need before you start

Most three-stage under-sink carbon systems need only basic tools and no drain connection, because they do not produce wastewater the way reverse osmosis does. Check the parts list in your box first. You will typically need:

  • an adjustable wrench and a towel or bucket for drips
  • a utility knife or tubing cutter for clean tube ends
  • a drill and bit only if the manual calls for a new faucet hole
  • the cold water supply line, with a shutoff valve if one is present

Read the full manual and watch the manufacturer’s installation video before you start. The steps below are general. Your model’s manual wins where the two differ.

Step 1: Shut off the water and check the space

Turn off the cold water at the shutoff valve under the sink. Open the kitchen faucet to release the pressure in the line. Clear the cabinet, and check that you have room for the filter housings and the tubing without kinks.

Step 2: Mount the filter head or bracket

Fix the filter head or mounting bracket to the inside of the cabinet wall or the floor. Keep it near the cold line and clear of the trash can and any pull-out drawers. Leave enough room to change the cartridges without removing the head.

Step 3: Connect the cold supply

Use the supplied adapter or saddle valve to take water from the cold line. Many kits use a quick-connect fitting. If the fitting is a compression type, tighten it firmly but do not over-tighten, or you can crack the fitting. Reconnect the shutoff valve if you removed it.

Step 4: Connect the tubing and faucet

Run the tubing from the supply to the filter inlet, then from the filter outlet to the faucet. Brondell describes color-coded tubing and quick-connect fittings for this step. Cut each tube square and push it fully into the fitting until it seats. A tube that is not fully seated is a common source of leaks.

If you are mounting a new faucet, install it on the counter first, then route the tubing through the hole. Check the faucet’s own instructions for the spacing and the gasket.

Step 5: Flush the filters

Turn the water back on slowly. Open the new faucet and let water run for several minutes, or for the volume the manual gives, so the carbon fines and air clear out. A small amount of air in the lines and some cloudiness at first are normal. They should clear within a few minutes of running water.

Do not drink the first water through the system until it runs clear.

Step 6: Check for leaks

Look under the sink at every fitting, the filter head, and the tubing for drips. Dry a fitting with a towel and check it again after a few minutes. Tighten a leaking nut gently, and only if the fitting is threaded. If a quick-connect fitting leaks, pull the tube out, re-cut the end square, and push it back in until it clicks.

Leave the system running for about an hour, then check again. Keep a bucket and towel under the sink for the first day.

Common problems and fixes

  • Air in the lines. Run the faucet until the sputtering stops. This is normal after changing a cartridge.
  • Slow flow. A new carbon block can slow flow for the first few gallons. If flow stays slow, check that the inlet valve is fully open and that the cartridges are seated correctly.
  • A drip at a fitting. Check that the tube is fully seated and cut square. Replace an old or damaged fitting ring if the manual includes one.
  • Water that tastes or smells odd. Run more water. If the taste persists, check the cartridge dates and the installation order.

Finding replacement filters

Use the model number on the filter head, the box, or the manual to order the right cartridges. Brondell sells replacement filters on its website and through retailers. Filters that look similar may not fit or may not carry the same certifications, so check the model before you buy.

If you cannot find the right cartridge, contact the manufacturer’s customer service with the model number and the box or receipt.

What the certifications mean for this system

Brondell lists its carbon systems as WQA-certified to NSF/ANSI standards. In general:

  • NSF/ANSI 42 covers aesthetic issues such as chlorine taste and odor.
  • NSF/ANSI 53 covers health-related contaminants, including some lead and PFAS claims.
  • NSF/ANSI 401 covers emerging contaminants, such as some pharmaceuticals.

Each certification lists specific contaminants and test conditions. Check the system’s performance data sheet for the exact list before you rely on a claim.

For the broader choice between filter types, see our guide to drinking water filtration systems compared. If you are still weighing whether an under-sink filter is worth the effort, read is an undersink water filter worth it. For a reverse osmosis install instead of a carbon system, see how to install an under-sink reverse osmosis system.

The complete guide to under-sink and countertop systems

Drinking Water Filtration Systems Compared: Under-Sink and Countertop
Read the guide

Keep exploring

Guides from other topics

All topics →