Under-Sink and Countertop Systems

How to Install a Frigidaire PureSource Ultra Refrigerator Water Filter

How to swap a Frigidaire PureSource Ultra refrigerator water filter: remove the old cartridge, install the new one, flush it, and reset the filter light.

On this page
  1. Before you start
  2. Step 1: Find the filter and its release
  3. Step 2: Remove the old filter
  4. Step 3: Install the new filter
  5. Step 4: Flush the new filter
  6. Step 5: Reset the filter light
  7. Common questions
  8. When to change the filter

Before you start

Check your refrigerator’s manual first. Frigidaire has used several filter designs over the years, and the release method and reset steps differ between models. The steps below describe how these filters are typically swapped. Where your manual says something different, follow the manual.

Have a towel ready for drips, and a dry cloth for the filter housing. Note the date on the old filter if the fridge logs it.

Step 1: Find the filter and its release

The filter location depends on the model. It is often inside the fresh-food compartment, in an upper corner or behind the grille, and on some models it sits in a compartment on the outside of the refrigerator. Some models have a filter housing that you turn, and others use a push release. Check the manual for your model’s location and release type.

Step 2: Remove the old filter

On many twist-lock models, turn the filter counterclockwise about a quarter turn until it releases, then pull it straight out. On push-release models, press the release button and pull the filter out. Expect a small amount of water to drip from the housing. Keep the towel under the housing while you work.

Do not force a filter that will not turn. Check the manual for the release method, and make sure you are turning the right way.

Step 3: Install the new filter

Remove the cap from the new filter, if it has one, and line up the filter with the housing. On twist-lock models, push the filter in and turn it clockwise until it locks. You should feel it seat. On push-release models, push it in until it clicks.

Check that the housing does not leak after the filter is in place. If the fridge has a bypass plug on the housing, that plug is used only when no filter is installed. Do not use it with a new filter.

Step 4: Flush the new filter

A new filter needs to be flushed before its water is used for drinking or ice. Many manufacturers recommend running water through the dispenser for a set volume. A common figure is about two to three gallons, but check the manual for the exact amount. The first water may look cloudy or have a slight taste. This is normal carbon fines and air, and it should clear as you run more water.

Do not drink or make ice from the first water until it runs clear.

Step 5: Reset the filter light

Most fridges with a filter indicator need a reset after a new filter is installed. The method varies by model. Some use a dedicated reset button, and others require holding a button for a few seconds. Check the manual for the exact steps, and reset the indicator only after the new filter is installed and flushed.

Common questions

How do I replace a Frigidaire PureSource Ultra filter? Use the steps above: find the filter, release it, remove the old one, install the new one, and flush it. Use the manual for your model’s release method.

How do I reset the filter light? Most Frigidaire models reset by holding a reset control for a few seconds after the new filter is in place. Check your manual, because some models reset in a different way.

Does a Frigidaire filter remove PFAS? Not every refrigerator filter does. Check the filter’s performance data sheet for PFOA and PFOS, and confirm which NSF/ANSI standard lists them. Do not rely on a general claim on the box or in a store listing.

How much water should you run through a refrigerator filter? The manufacturer’s manual sets the amount. Many recommend about two to three gallons, run through the dispenser before you use the water. Follow the manual.

When to change the filter

Change the filter on the schedule in the manual, or when the filter light tells you to. Filters that are left in past their life can clog or reduce performance, and the filter light is only a reminder. Mark the date on a calendar so you do not depend on the light alone. For the general schedule across refrigerator filters, see how often to change a refrigerator water filter.

If you are weighing a fridge filter against a dedicated under-sink or countertop system, see drinking water filtration systems compared.

The complete guide to under-sink and countertop systems

Drinking Water Filtration Systems Compared: Under-Sink and Countertop
Read the guide

Keep exploring

Guides from other topics

All topics →