Short answer
Many standard residential reverse osmosis (RO) systems send about 3 to 4 gallons of water down the drain for each gallon of treated water they make. High-efficiency models can do much better, and some reach ratios close to 1 to 1. The exact figure depends on the model, your water pressure, the water temperature, and how well the system is maintained. Check your model’s specifications for its stated ratio.
Why an RO system sends water to the drain
The membrane separates the water into two streams. One stream is the treated water you drink. The other carries the dissolved salts and other rejected material away. That reject stream also keeps the membrane surface clean. Without a steady flow across it, the membrane can foul and lose performance faster.
For this reason, residential systems are designed with a fixed amount of reject flow, usually set by a flow restrictor. The reverse osmosis pillar guide explains the stages in more detail.
Typical ratios by system type
- Standard tank-based systems commonly send several gallons to the drain for each gallon they store. Their ratio is set mainly by the flow restrictor and the membrane.
- Tankless and high-efficiency systems often use a permeate pump or other design features to reduce the reject flow. Their ratios can be much lower, and some are close to 1 to 1. These usually need more water pressure to work well.
- Certified high-efficiency models may carry the EPA WaterSense label. Check the label and the manufacturer’s stated ratio, rather than relying on a general claim.
A ratio is only a number on a specification sheet until you know how your system performs in your home. Water quality and pressure can move the actual figure.
What changes the ratio
- Water pressure. Low feed pressure makes the membrane less efficient, which can increase waste. Check your pressure before you blame the system.
- Water temperature. Colder water is more viscous, which slows production and can change the ratio.
- Feed water quality. Water with higher dissolved solids usually needs more reject flow to keep the membrane clean.
- Filter and membrane age. Clogged prefilters or a worn membrane can make the system work harder.
- The auto shutoff valve. A faulty valve can keep the system running and sending water to the drain when the tank is full. Check it if the drain runs constantly.
How to measure your own system
A simple bucket test shows roughly how much water your system sends to the drain:
- Empty the storage tank, or wait until it is nearly empty, so the system will refill it.
- Place a bucket or measuring container under the drain line, and let the system refill the tank.
- Measure how much water collected in the drain bucket, and compare it with the amount the tank refilled.
Divide the drain volume by the volume the tank refilled. The result is your approximate ratio. It is a rough test, and it works best when no water is drawn from the faucet during the refill.
Ways to reduce waste
- Keep the prefilters and membrane current. Clogged or worn parts can increase waste.
- Check the feed pressure against your model’s stated minimum.
- Consider a high-efficiency model if waste matters to you, and check that it suits your water pressure and water quality. Some high-efficiency designs need more pressure.
- Do not alter the flow restrictor to change the ratio. Its size is matched to the membrane, and changing it can shorten the membrane’s life.
Reducing waste is a trade-off. A lower reject flow can mean the membrane is more likely to foul and need cleaning or replacement sooner. Ask about this when comparing models.
Reusing reject water
Some households reuse reject water for tasks that do not involve people drinking or bathing in it. Reject water is more concentrated than tap water, so it is not suitable for drinking, cooking, or bathing. Check your local rules before using it for cleaning, flushing, or on plants, because some areas restrict how reject water can be used, and highly concentrated water can harm some plants.
Also check how your water is billed. In some areas, drain water from a home system may count toward a metered sewer charge. If your utility bills for sewer use, the drain water may add to that cost.
For problems such as constant running or slow production, see our troubleshooting guide. For the timing of membrane replacement, see how often to replace an RO membrane. For the water-quality side of RO, see what TDS level reverse osmosis water should be.