Under-Sink and Countertop Systems

How to Change the Filters in an Under-Sink RO System

Step-by-step guide to changing the filters in an under-sink RO system: shutting off water, relieving pressure, swapping cartridges, and flushing.

On this page
  1. What you need
  2. Step 1: Shut off the water
  3. Step 2: Relieve the pressure
  4. Step 3: Remove and wash the pre-filter housings
  5. Step 4: Install the new pre-filters
  6. Step 5: Replace the membrane or post-filter when due
  7. Step 6: Restart and flush
  8. If a housing is stuck
  9. Keeping a schedule

What you need

Changing the filters on an under-sink reverse osmosis (RO) system usually takes 30 to 45 minutes. Gather these before you start:

  • the replacement filter set for your model, including the pre-filters, and the membrane or post-filter if due
  • a plastic filter wrench, which many kits include
  • towels, or a small bucket or tray to catch spilled water
  • mild dish soap, if you want to clean the housings

Check the manual for the exact cartridges your model takes. Filters that look similar may not fit.

Step 1: Shut off the water

Turn off the cold water supply valve that feeds the RO system. Then close the valve on top of the storage tank by turning it so the handle sits perpendicular to the tube. Both valves need to be closed before you open any housing.

Step 2: Relieve the pressure

Open the RO faucet and let it run until the water stops completely. This releases the pressure in the system so water does not spray when you open the housings. Leave the faucet open while you work.

Step 3: Remove and wash the pre-filter housings

Place a towel or bucket under the unit. Use the filter wrench to loosen each plastic housing. Most turn counterclockwise, but check your unit, because some differ. Pull the housing down, discard the old cartridge, and empty the leftover water. Wash the empty housings in warm water with a little dish soap, then rinse them well.

Step 4: Install the new pre-filters

Insert the new sediment and carbon cartridges into their housings. Check that each rubber O-ring is seated at the top of the housing. Screw the housings back on and hand-tighten them firmly. Do not over-tighten with the wrench. Plastic housings can crack, and an over-tightened O-ring can pinch and leak.

Step 5: Replace the membrane or post-filter when due

The RO membrane is usually replaced every two to three years, and the post-carbon polishing filter about once a year. These are changed less often than the pre-filters, but they still need a date.

To change either one, press in the collet ring on the quick-connect fitting and pull the tubing out. Then install the new part. Pay attention to the flow-direction arrow printed on the new part, and install it facing the way the arrow shows. Reconnect the tubing and push it in until it seats.

Step 6: Restart and flush

Turn the cold supply and the tank valve back on. Check every housing and fitting for leaks with a towel and a flashlight. Open the RO faucet and let the system run. Manufacturers differ on the flush. A common approach is to let the faucet run for about ten minutes, or to empty the tank a couple of times, to clear loose carbon dust. Follow your manual’s instructions if they differ.

Once the flush is done and the water runs clear, the system is ready for drinking.

If a housing is stuck

Do not force a housing that will not turn. Check that the water is fully off and the faucet has been opened to release pressure. Put a towel over the housing and try again with steady pressure. If it still will not move, check whether the housing is cross-threaded, or whether an old O-ring is stuck. A stuck housing is usually a sign to pause and check the manual, not to use more force.

Keeping a schedule

The most common cause of poor RO output is a late filter change. Set a calendar reminder for the pre-filters, usually sooner than the membrane, and note the install date on each cartridge with a marker. Keep the membrane and post-filter on their own reminders. Your manual gives the exact schedule for your model, and it should be the guide, because water use and local conditions change how fast a filter wears.

For the install steps before you start filtering, see how to install an under-sink reverse osmosis system. For tank sizing and the pre-charge check, see how big a storage tank does an under-sink RO need?. For the wider comparison of product types, see drinking water filtration systems compared.

The complete guide to under-sink and countertop systems

Drinking Water Filtration Systems Compared: Under-Sink and Countertop
Read the guide

Keep exploring

Guides from other topics

All topics →