Pitcher and Gravity Filters

Do You Need to Soak a New Brita Filter Before Using It?

Most new Brita Elite filters need no soak, while white Original filters need a 15-second rinse and older ones a 15-minute soak. Here's the step-by-step.

On this page
  1. The short answer
  2. Check which filter you have
  3. Elite (blue): no soak and no rinse
  4. Original (white): rinse, and soak if it’s old
  5. Stream and faucet systems
  6. Why rinsing and soaking help
  7. Discard the first three pitchers
  8. Water temperature
  9. Set the indicator

The short answer

It depends on the filter color. A new blue Brita Elite doesn’t need a soak or a rinse before use. A white Brita Original (formerly “Standard”) needs a 15-second cold-water rinse before you install it. If the white filter is more than a year old, Brita recommends soaking it for 15 minutes before first use.

Check which filter you have

Filter Color Before first use
Elite Blue No rinse, no soak. Install, fill with cold tap water, discard the first three pitchers
Original (formerly Standard) White Rinse 15 seconds with cold water. Soak 15 minutes if the filter is more than a year old
Stream Gray Flush 15 seconds with cold water
Faucet system Varies Flush as the model’s manual says. Brita’s faucet system FAQ says five minutes for a new filter

If you can’t tell which filter you have, look at the color of the cartridge and the name on the packaging.

Elite (blue): no soak and no rinse

Brita says no pre-rinse is needed for the Elite filter. Wash your hands, remove the filter from its bag, and insert it into the reservoir. Line up the groove on the filter with the notch in the reservoir, and press firmly for a tight seal. Fill the reservoir with cold tap water, and discard the first three pitchers of filtered water or use it to water plants.

Original (white): rinse, and soak if it’s old

Brita’s instructions for the white Original filter include a 15-second cold-water rinse before you insert it. After installing, follow the same steps as the Elite: fill with cold tap water and discard the first three pitchers.

If the white filter has been sitting around for more than a year, Brita recommends soaking it in water for 15 minutes before use. Brita’s pitcher FAQ and its replacement-filter FAQ both give this advice.

Stream and faucet systems

Brita Stream filters (gray) are flushed for 15 seconds with cold water before use. Brita’s faucet systems have their own instructions. For the faucet systems Brita sells under the FF-100 and SAFF-100 names, its FAQ says to flush a new filter for five minutes. If a faucet system hasn’t been used for several days, Brita says to run water through the filter for about 30 seconds before drinking.

Why rinsing and soaking help

Brita doesn’t spell out the reasons for each step. In general, rinsing and soaking a carbon filter serve three purposes. They wet the filter material, they clear loose carbon dust, and they let trapped air escape. Air pockets can make water flow slowly, and loose carbon dust can make early fills look cloudy. Our inference from those steps is that they help the filter start working as designed.

Brita does say that carbon dust in the first few fillings is normal, especially with its older filters.

Discard the first three pitchers

Brita recommends discarding the first three pitchers of filtered water from a new filter. You can use that water to water plants. This clears out the initial carbon dust and any loose material before you drink from the filter.

Water temperature

Use cold tap water with Brita filters. For the Elite, Brita’s pitcher setup instructions say not to use hot water, with a range of 32°F to 85°F (0°C to 29°C).

Set the indicator

Set up the filter life indicator after you install the new filter. The steps differ for the Original and Elite, so follow the manual for your pitcher. Setting the indicator keeps the replacement schedule accurate.

If the filter still flows slowly after you install it, check the pitcher flow guide for the most common causes. For the full Brita lineup, see the Brita filter review.

The complete guide to pitcher and gravity filters

ZeroWater vs PUR vs Brita: Which Pitcher Filter Is Best?
Read the guide

Keep exploring

Guides from other topics

All topics →