The short answer
A faucet filter is a point-of-use add-on that treats the water coming out of one tap. It can improve taste and reduce some contaminants, depending on the cartridge and its certifications. It does not soften hard water, and it cannot make unsafe water safe. Choose it for a specific problem, check the certifications for that problem, and keep it on schedule.
What to check before buying a faucet filter
- Certifications for your concern. Look for the specific contaminants on the current data sheet, not a general claim of “purifies water.”
- Aerator type. Many systems mount where the faucet’s aerator screws on. Some faucets have a non-removable aerator, and the filter will not fit. Check your faucet before you buy.
- Hot water. Don’t run hot water through a faucet filter unless the manufacturer says it is safe. Some reviews report hot water damaging filter heads.
- Rated life. Filters are rated by gallons or months, whichever comes first. Know which applies to the model you are buying.
- Fit and space. Some systems are bulky and can be hard to move around in a crowded sink.
Brita faucet systems
Brita’s faucet systems (the FF-100 and SAFF-100 models, according to Brita’s FAQ) are rated for 100 gallons, about four months. Brita advises flushing a new filter for five minutes before use, because the rated life starts after the flush. If the system sits unused for several days, Brita says to run water through the filter for 30 seconds before you drink it.
Reviewers report mixed results. Some praise the easy install and the indicator light. Others describe leaks at the seams, a filter that comes loose during use, or a metallic taste. Those reports are not from testing, so weigh them against your own faucet and water.
PUR faucet systems
PUR faucet systems are commonly described as lasting up to three months or 100 gallons, whichever comes first. Some users say the lever switch is sensitive, the housing is fragile, or the indicator light is unreliable. Others say the water tastes good and the filters are easy to swap.
Models differ, so check the rated life and certifications on the box for your exact model. A filter that fits one PUR model may not fit another.
Troubleshooting checklist
If your filter isn’t working, check these in order:
- The lever or switch is set to filtered.
- The cartridge is seated correctly and the system is tight on the faucet.
- The cartridge is within its rated life. An old cartridge is the most common cause of slow flow and off taste.
- You flushed a new cartridge as the instructions say.
- Your water pressure is adequate. A filter cannot fix low pressure.
- You are not running hot water through a cold-water filter.
- The aerator is compatible with the adapter you installed.
If the system still doesn’t work, contact the manufacturer with the model number and purchase details.
Slow flow
Slow flow usually has one of four causes: an old or clogged cartridge, a cartridge that was installed improperly, low water pressure, or a faucet aerator that restricts flow. A new cartridge that is not flushed can also run slowly for the first few gallons.
Replace the cartridge if it’s past its rated life. If it is new and still slow, reinstall it, flush it as directed, and check the aerator and pressure.
Leaks and drips
Leaks usually come from the adapter, a worn gasket, or a cartridge that isn’t seated. Some users report drips after the water is shut off. Check that the adapter fits your faucet’s thread, that the gaskets are in place, and that you have not overtightened the parts. Overtightening can crack plastic housings. Replace any cracked or worn part instead of forcing it.
The indicator light
Many faucet filters have an indicator that tracks filter life. Some users report that the light is inaccurate or flickers. If your light doesn’t match what you expect, don’t rely on it alone. Keep a note of the date you installed the cartridge, and compare it with the rated life for your model.
When you install a new cartridge, reset the indicator following the manual.
What a red light means
A red light usually means the cartridge has reached the end of its rated life. Replace it. Don’t assume the water is still filtered to its certified level just because the water still flows. If the light is red and you can’t replace the cartridge right away, switch the system to unfiltered water and use another source for drinking until you can.
Hard water: taps won’t soften
Most faucet filters are not designed to remove the minerals that cause hardness, so they will not stop scale in kettles, showerheads or dishwashers. If hard water is the problem, look at a water softener or a scale-reduction system for the whole house. A faucet filter can still help with taste or chlorine, but it won’t change hardness.
Should you filter your tap water?
Start with your water utility’s annual water quality report, often called the Consumer Confidence Report in the United States. It lists what the utility tested for and the levels found. Lead often comes from home plumbing, so a utility report may not show it. A tap test for lead is more useful for that.
If the report shows nothing you’re concerned about and the taste is fine, a faucet filter may not be necessary. If you have a specific concern, such as lead or chlorine taste, choose a filter certified for that contaminant. For a broader comparison of pitcher options, see the ZeroWater vs PUR vs Brita comparison.
Buy from authorized sellers
Some reviewers report filters that don’t perform as described and may be counterfeit. Buy from the manufacturer or a reputable retailer, check the packaging, and be cautious about unusually cheap replacement cartridges.
If you use well water or your water is microbiologically unsafe, a faucet filter is not a substitute for disinfection. See the simplest way to purify water at home for the basics.