The short answer
Black Berkey elements need priming before first use. Attach the tan priming button to each element, press it against a cold faucet, and let a small, steady stream of cold water run until the element’s outer surface sweats evenly from top to bottom. Then reinstall the element and run the first batch through to waste. PF-2 fluoride filters are primed differently: flush each end under cold water until the water runs clear.
What you need
- Your Black Berkey elements, new or freshly cleaned, with the priming button, wing nut and washer that come in the box
- A cold water faucet where you can press the priming button firmly against the outlet
- Optional: the Black Berkey Primer, a hand-pump tool sold separately. It’s designed only for Black Berkey elements, and it can help if your faucet is short or hard to reach. You don’t need it to prime.
Priming Black Berkey elements, step by step
- Remove the wing nut and washer from the element’s threaded stem.
- Place the tan priming button flush onto the stem.
- Hold the element against the cold faucet, pressing the priming button firmly.
- Turn on a small, steady stream of cold water. Don’t use hot water.
- Hold it there until the outer surface of the element sweats evenly and forms small beads from top to bottom. Typical guides describe 30 to 60 seconds, and sometimes a few minutes for a tight or stubborn element.
- Remove the priming button, put the washer and wing nut back on, and reinstall the element in the upper chamber. Hand-tighten the wing nut.
- Fill the upper chamber and let the first batch run through to waste from the lower chamber.
Repeat for each element. Don’t skip one, because a single unprimed element will filter slowly and can leave your flow uneven.
Priming PF-2 fluoride filters
PF-2 fluoride filters are primed differently from Black Berkey elements:
- Remove or leave the caps as the instructions for your filter say.
- Attach the priming adapter or rubber button to the top end, the end opposite the flow arrow.
- Press it against the cold tap and let water flow for at least 30 seconds.
- Flip the filter and prime from the other end until the water runs clear.
- Collect a little water in a clear glass and hold it to the light. It should look clear, not cloudy.
No tap pressure? The soak method
If you can’t prime with the faucet, Berkey describes a soak method. It works, but Berkey says it is less effective than the priming button and won’t purify as fast. Use it only when the button method isn’t possible.
- Remove the elements from the upper chamber.
- Fill the lower chamber with water.
- Place the elements upside down, stems up, in the water. Weigh each one down with a cup so it stays submerged for several hours. Keep the stem openings above the water so the water is pushed through the pores, not in through the stems.
- Reassemble the elements into the upper chamber while they still hold water. Empty the lower chamber, set the upper chamber back, and fill it right away.
- Let the lower chamber run to waste, then refill the upper chamber.
Berkey’s FAQ gives this method and recommends using the priming button when you can.
Re-prime after cleaning
Berkey recommends cleaning the elements every three to six months, or when the flow slows. Scrub each element with a Scotch-Brite pad or a stiff brush until you see a little black on the pad. Don’t use soap. Rinse, then re-prime with the button before you reinstall. The Berkey lifespan guide explains the cleaning schedule in more detail.
Checking that the prime worked
- Flow. A properly primed element should drip steadily. If it’s slow right after priming, prime it again.
- Clarity. The first batches may look cloudy or carry small particles. Run and discard the first batch, then check that the water runs clear.
- Red dye test. Berkey’s red dye test should be run after priming. It checks whether an element is still working, and it’s described in the Berkey lifespan guide.
Don’t use soap on the elements at any stage. Don’t let the elements freeze, and keep them dry when they are stored.
How this compares with ProOne
ProOne says its filters don’t need priming, and a reviewer who used one in a Berkey agreed that the ProOne filters are ready to use after a quick rinse. Don’t assume the Berkey steps apply to ProOne elements. For the naming and system comparison, see whether ProOne and Propur are the same and the gravity water filter guide.
If you are filtering water from an unknown or unsafe source, boil it first. A priming step doesn’t change what the filter can and can’t remove. See the simplest way to purify water at home.