Water Treatment Basics

How do drinking water filters work?

Most home water filters combine a few basic processes: a physical screen, carbon adsorption, ion exchange and membranes. Here is how each one works.

On this page
  1. A physical barrier
  2. Adsorption on activated carbon
  3. Ion exchange
  4. Membranes: reverse osmosis and ultrafiltration
  5. UV light
  6. Why most filters have several stages
  7. Why filters stop working
  8. Check the certified claim

Most home drinking water filters use one or more of four basic processes: a physical barrier, adsorption onto activated carbon, ion exchange, and a semipermeable membrane. Some add ultraviolet (UV) light as a final disinfection stage. Most systems combine several of these, in an order that protects each stage from the one before it. Knowing how each process works makes it easier to read a product’s claims.

A physical barrier

The simplest process is screening. A mesh or porous material traps particles that are larger than its openings. Sand, rust, silt and visible debris are caught this way. Sediment filters are almost always the first stage in a multi-stage system, because they stop particles from clogging the finer stages behind them.

Filters in this category are often rated in microns, which describes the size of particle the material is designed to trap. A micron rating does not tell you which microbes or chemicals the filter removes. For that, look for a certification that tests the specific claim.

Adsorption on activated carbon

Activated carbon has a very large internal surface area. As water passes through, dissolved chemicals stick to that surface. This is adsorption, and it is the main process behind carbon filters.

Carbon is effective for chlorine, taste and odour, and many organic chemicals. It is less effective for dissolved salts and for many metals unless the product is specifically designed for them. It also works only while it has capacity left. Once the carbon is used up, it stops removing contaminants well and can release some of what it has captured. Replacing carbon on schedule is part of the filter working correctly.

Carbon comes in two common forms. Granular activated carbon (GAC) has loose granules and a faster flow. Carbon block is compressed carbon with a finer structure and more contact time, which helps some contaminants that are harder to capture.

Ion exchange

Ion exchange uses resin beads that swap one ion for another. In a softener, the resin trades calcium and magnesium (the minerals that cause hardness) for sodium or potassium. In some filters, resin swaps unwanted ions for others, which can reduce certain metals or nitrate depending on the resin.

Softeners need periodic recharging with salt or potassium. Cartridge-type ion exchange media are usually replaced rather than recharged. Ion exchange does not remove most contaminants, so a softener is a different kind of product from a safety filter.

Membranes: reverse osmosis and ultrafiltration

Membranes separate water from contaminants by size or by charge and solubility.

Reverse osmosis (RO) uses pressure to push water through a membrane that rejects most dissolved salts and many contaminants. The water that passes through is collected in a storage tank or sent directly to the tap, and the rejected material leaves as a concentrate stream down the drain. RO needs enough water pressure to work, and the membrane needs pre-filters to protect it from sediment and chlorine.

Ultrafiltration (UF) uses a membrane with larger pores than RO. It removes particles and many microbes, but it does not remove dissolved salts. It usually does not need the storage tank or the concentrate loss that RO involves.

Our article on ultrafiltration covers UF in more detail, and the types of home water filters article compares the main options side by side.

UV light

UV disinfection passes water near a UV lamp. The light inactivates many bacteria and viruses, which means they can no longer reproduce. UV does not remove chemicals or particles, so it is normally placed after the sediment and carbon stages. Its effectiveness depends on the water being clear enough for the light to reach the microbes, and on the lamp working properly. Replacing the lamp on schedule is essential.

Why most filters have several stages

A single process rarely does the whole job. A typical multi-stage system might look like this:

  1. A sediment pre-filter removes particles.
  2. A carbon stage removes chlorine and taste and odour compounds.
  3. A membrane or specialised medium removes the target contaminants.
  4. A final stage, such as a carbon post-filter or UV lamp, polishes the water or inactivates microbes.

The order matters. Sediment that reaches the membrane can clog it. Chlorine that reaches an RO membrane can damage it. Carbon that is clogged with sediment loses contact with the water. This is why manufacturers specify pre-filters and replacement schedules.

Why filters stop working

Filters do not fail suddenly in most cases. They lose capacity gradually, and a sediment pre-filter that is overdue can restrict flow long before the rest of the system stops working. Carbon can release captured material when it is spent. Membranes lose performance as they foul. Replacement on the manufacturer’s schedule, whichever of time or volume comes first, is the simplest way to keep a system doing what it was certified to do.

Check the certified claim

When a product says it removes something, look for the standard and the specific claim. Certification from a body such as NSF International tests a product for named contaminants under defined conditions. Our article on NSF certifications explains how to read the claims, and our article on how often to change a home water filter covers the replacement timing that keeps them working.

The complete guide to water treatment basics

Types of Home Water Filters and Treatment Systems Compared
Read the guide

Keep exploring

Guides from other topics

All topics →