Pitcher and Gravity Filters

Why Is My Brita Pitcher Filtering So Slowly?

A slow Brita pitcher is often trapped air, a clogged or overdue filter, or sediment. Here's how to tell normal Elite speed from a real problem and fix it.

On this page
  1. The short answer
  2. Is my flow normal?
  3. Fix it in this order
  4. Sediment and hard water
  5. Aeration and how you fill
  6. Hot water and temperature
  7. When to replace the filter
  8. When to stop and call Brita

The short answer

A slow Brita pitcher usually has one of three causes: air trapped in the filter, a filter that is clogged with sediment, or a filter that is past its rated life. Brita says an Elite filter should take at most 10 to 15 minutes to filter a full reservoir, so some slowness is normal. If your pitcher takes much longer than that, work through the fixes below in order.

Is my flow normal?

Start with the filter color and the size of the reservoir.

  • Elite (blue). Brita says a full reservoir should take at most 10 to 15 minutes. The first few fills can seem slower than later ones.
  • Original (white). Brita does not give the same time range in the sources we reviewed. If it is clearly slower than your other pitchers, or slower than it was when new, look at the causes below.

If the filter is past its rated life, slow flow is expected. Brita rates the Elite at 120 gallons and the Original at 40 gallons. Track your gallons or follow the filter indicator. For the lineup, see the Brita filter review.

Fix it in this order

  1. Check the filter’s age. If it’s past its rated life, replace it. Replacement is usually the fix.
  2. Reseat the filter. Pull it out, then press it straight down into the reservoir until it seats firmly, with no gaps. Don’t twist it.
  3. Soak and shake. Submerge the filter in cold water, and tap or shake it gently to dislodge trapped air bubbles.
  4. Rinse. Run the filter under cold tap water for 10 to 30 seconds to clear loose carbon dust.
  5. Refill and time it. Fill the reservoir to the max fill line and time the next full reservoir.

If the pitcher is still slow after these steps, the filter is likely clogged or worn. Replace it.

Sediment and hard water

Sand, rust and limescale in tap water can clog the filter’s pores. Brita says high sediment levels can clog a filter quickly and shorten its life, and that you may need to replace the filter more often. Hard water has a similar effect, and Brita advises replacing filters more often when water is hard.

If sediment is a recurring problem, look at upstream protection, such as a sediment prefilter at the point where water enters the house. That is a separate system from the pitcher.

Aeration and how you fill

Air in the water stream can slow filtering. Brita says to avoid fully opening the faucet to a full stream when you fill the reservoir, and to avoid pouring tap water directly onto the top of the filter. A gentler fill reduces air in the reservoir.

Hot water and temperature

Use cold tap water. Brita’s Elite instructions say not to use hot water, with a range of 32°F to 85°F (0°C to 29°C). Stick with cold water for every fill.

When to replace the filter

Replace the filter when:

  • The indicator shows the filter is at the end of its life, or the red light blinks
  • You have passed the rated gallons (120 for Elite, 40 for Original)
  • The pitcher is still slow after you have reseated, soaked, rinsed and refilled
  • You have seen a clear change in taste or odor

Brita’s filter life figures assume typical household use, so heavy use or hard or sediment-rich water will shorten the life.

When to stop and call Brita

If the filter is new, seated correctly, rinsed, and the pitcher still runs far slower than Brita’s guidance, contact Brita support with the model number and purchase details. Brita’s pitchers come with a 30-day money-back guarantee and a one-year warranty against damage, according to its FAQ. Check the current terms before you rely on either.

For the first-use steps on a new filter, see whether you need to soak a new Brita filter.

The complete guide to pitcher and gravity filters

ZeroWater vs PUR vs Brita: Which Pitcher Filter Is Best?
Read the guide

Keep exploring

Guides from other topics

All topics →