Water Treatment Basics

How much does a whole house water filtering system cost?

Estimates for a whole house water filter run from about $1,500 to $10,000 installed, depending on system type and water. See what drives price and upkeep.

On this page
  1. Typical costs by system type
  2. What installation adds
  3. Ongoing costs
  4. A five-year estimate
  5. What changes the price
  6. Whole house or under-sink
  7. How to get a useful quote

A whole-house water filtration system typically costs somewhere between about $1,500 and $10,000 installed, based on published estimates. The range is wide because the systems differ a lot. A basic sediment or carbon setup costs much less than a combined softener, filter and UV system. Installation, plumbing changes and local labour rates also move the total. Treat any single figure as an estimate, and get a written quote for your home before you decide.

Typical costs by system type

Published cost guides group whole-house systems into a few types. The table below shows the kinds of systems and what they usually involve. The figures are rough, and you should expect quotes to differ.

System type What it usually includes Rough installed range
Basic sediment or dual-stage carbon Sediment and carbon cartridges in a housing Low end of the range
Multi-stage carbon or KDF Several stages, often with a larger tank Middle of the range
Water softener Ion exchange tank and brine system Middle to upper range
UV disinfection Lamp and chamber, usually added to another stage Adds a few hundred to a few thousand dollars
Combined softener and filter Softener plus carbon or specialty media Upper range

Check the actual quote against the table. If a quote seems far outside these ranges, ask what is included and why.

What installation adds

Installation is a large part of the total for most homes. A plumber may need to cut into the main line, install bypass valves, add a drain connection for backwash or brine, and secure the unit. Some jobs need a permit. Costs rise if the unit has to go in a tight space, if the pipe runs are long, or if the house has older plumbing that needs work.

Ask for installation to be listed as a separate line in the quote. That makes it easier to compare bids and to see what is included, such as bypass valves, fittings, and a warranty on the work.

Ongoing costs

The purchase price is only part of the cost. Plan for these running costs:

  • Replacement cartridges or media. Sediment pre-filters often need changing every few months. Carbon and specialty media last longer but still need replacing.
  • Salt or potassium for a softener, and the electricity it uses.
  • UV lamp replacement and the power needed to run the lamp.
  • Service visits, if the system needs them.

Replacement intervals depend on your water and how much you use. Check the manufacturer’s rated life for each cartridge, in both months and gallons, and use whichever comes first.

A five-year estimate

Purchase price alone can be misleading. A simple way to compare two quotes is to total the cost over five years:

  1. Add the quoted equipment and installation.
  2. Estimate how many replacements you will need in five years, using the manufacturer’s rated life for each stage.
  3. Multiply by the replacement cost of each stage.
  4. Add salt, power and any service visits you expect.

Here is a worked example with placeholder numbers. Suppose a quote totals $2,000 installed, a sediment cartridge costs $40 and needs changing every six months, and a carbon cartridge costs $90 and needs changing every 12 months. Over five years, that is ten sediment changes ($400) and five carbon changes ($450), so the five-year total is $2,850 before salt or power. The numbers are invented for the example. Your own quotes and replacement prices will be different.

What changes the price

  • Your water test. If the results call for a single stage, the system can be simpler and cheaper. If they call for several treatment types, expect a larger system.
  • Household size. A larger household uses more water and may need a larger unit with higher flow.
  • Site access. A utility room that is easy to reach costs less to fit than a tight crawlspace.
  • Plumbing condition. Older pipes may need repair or replacement before the unit can go in.
  • Brand and warranty. Brand-name systems often cost more, and the warranty terms vary.

Whole house or under-sink

A whole-house system treats every tap, shower and appliance. If your main concern is drinking water, an under-sink or countertop system at the kitchen tap is usually much cheaper, and it may meet your needs. Our article on the downsides of a whole-house filter explains what whole-house systems do and do not offer, and types of home water filters compares the options.

How to get a useful quote

Ask each installer for:

  • The exact model and the stages it includes, with the manufacturer’s rated life for each.
  • The installation scope, including fittings, bypass valves, drain or brine connections, and any permit.
  • The replacement schedule and the cost of each replacement part.
  • The warranty on the equipment and on the installation.
  • Whether the quote is based on a water test. A quote without a test is a guess.

Our article on how often to change a home water filter explains the replacement timing that feeds into the running cost.

The complete guide to water treatment basics

Types of Home Water Filters and Treatment Systems Compared
Read the guide

Keep exploring

Guides from other topics

All topics →