The “seven steps of water filtration” usually describe how a public water utility treats water before it reaches your home. The list is not a standard, and different sources count the steps differently. The common version runs from screening and pH adjustment at the start, through coagulation, flocculation, sedimentation, filtration and disinfection, to storage and distribution. Most home filters do only a small part of that work, and some of the steps are not relevant to a home at all.
The seven steps at a utility plant
- Pre-treatment. Large debris, such as leaves and fish, is removed with screens. The pH may be adjusted at this stage.
- Coagulation. A coagulant, such as aluminium sulphate or an iron salt, is added. It neutralises the electrical charges on tiny suspended particles so they can start to stick together.
- Flocculation. The water is gently mixed so the particles bind into larger clumps called flocs.
- Sedimentation. The water sits in large basins, and gravity pulls the heavier flocs to the bottom. The settled material, called sludge, is removed.
- Filtration. The clearer water passes through beds of sand, gravel or activated carbon, which trap the fine particles that remain.
- Disinfection. A disinfectant, such as chlorine, chloramine, ozone or ultraviolet light, is applied to kill or inactivate bacteria, viruses and parasites.
- Storage and distribution. The water is held in storage and sent through pipes. A small residual of disinfectant is kept in the water so it stays protected on the way to homes.
Each step does a different job, and the steps depend on one another. Coagulation has to work before sedimentation, and the filtration step catches what the earlier steps miss. Disinfection comes last at the plant so that the residual can protect the water in the pipes.
What a home filter can and cannot replace
A home filter does not repeat the plant’s process. You cannot add coagulant at the kitchen tap, and a home sediment filter is not the same as a sand bed. Most home systems do some of the following:
- Sediment filtration catches particles that get past the plant or come from pipes and fixtures. It is similar in purpose to the plant’s filtration step.
- Carbon filtration removes chlorine and many organic chemicals. This means it can remove the disinfectant that the utility added to protect the water in the pipes.
- Reverse osmosis or ultrafiltration removes particles and, depending on the system, many dissolved substances or microbes.
- UV disinfection inactivates microbes at the point of use.
A home filter is not a substitute for the plant’s disinfection. If the water from your utility is treated and in compliance, a carbon or sediment filter improves taste and removes some chemicals, but it does not add a disinfectant. If your water has a microbial concern, such as a private well or a boil-water notice, follow the advice of your health department.
Why the disinfectant matters after the filter
Utilities keep a disinfectant in the water so that it remains safe in the pipes. Chlorine and chloramine are the two most common. A carbon filter removes both to some degree, and chloramine is harder to remove than chlorine. If you filter the water after the utility has disinfected it, the water at your tap may have less disinfectant than the water in the street. For most households on a well-run system, this is not a practical problem. It is worth knowing if you have a question about water quality or a notice from your utility.
Our article on filtration and purification explains the difference in more detail, and the chloramine article covers the chloramine question.
Where to find what your utility does
Your utility’s annual Consumer Confidence Report describes the disinfectant it uses, the treatment it applies, and any detected contaminants. It is the best source for your own supply. If the report does not answer a question, call the utility. The steps in a plant can vary by source and by facility, so the report is more reliable than a general list.
Bottom line
The seven steps describe a utility plant. A home filter usually does part of the job, and it does not replace the disinfection that protects the water in the pipes. Read your utility’s report to see what your supply receives, and test your water if you are on a private well. Our article on how drinking water filters work explains the processes a home filter uses.