Reverse Osmosis

Reverse Osmosis Troubleshooting: Blinking Lights and Common Faults

Troubleshoot an RO system with blinking lights, low water, leaks, or constant drain flow, with the checks to run before calling for service.

On this page
  1. Short answer
  2. Start with the manual
  3. Little or no water
  4. Slow flow at the faucet
  5. The system keeps running or draining
  6. Leaks
  7. Bad taste or odor
  8. Unusual noise
  9. When to stop using the water and call for service

Short answer

Most RO problems come from a short list of causes: a valve that is closed, a clogged prefilter, low household water pressure, a storage tank with the wrong air pressure, a loose fitting, or a faulty auto shutoff valve. Start with the simplest checks. Blinking light patterns and error codes differ by brand and model, so the light table in your manual is the reference for what a blink means.

Start with the manual

Light patterns and fault codes are specific to each model, and a pattern that means one thing on one system can mean something else on another. Find your model’s light table, and note the pattern you see. If the manual does not explain it, contact the manufacturer’s support with the model and serial numbers.

Little or no water

Check these in order:

  1. The water supply valve. Many systems tap into the cold line with a saddle valve. Confirm that it is open.
  2. The storage tank valve. Tanks often have a valve between the tank and the line to the faucet. Confirm that it is open.
  3. Tank air pressure. With the tank empty and the water off, check the pre-charge on the tank’s air valve. The manual gives the correct figure for your tank. An incorrect pre-charge reduces how much water the faucet delivers.
  4. Household water pressure. The system needs enough pressure to run. Many models list a minimum of about 40 psi. See our article on RO feed pressure.
  5. Prefilters. A clogged sediment or carbon prefilter reduces flow. Replace it if it is due or overdue. See the sediment prefilter guide.
  6. Refill time. Production is slow, so a tank can take hours to refill after heavy use. If the system has been running for only a short time, allow it to finish before you judge the output.

Slow flow at the faucet

A slow faucet is usually a clogged prefilter, low pressure, or a tank that is nearly empty. A newly installed system can also have debris from the pipes or sediment in the filters, which clogs the first filters quickly. Run the faucet until the water runs clear after a filter change or a new installation.

If the flow drops again soon after you change the filters, the cause may be the quality of the incoming water. Have the water tested.

Do not change the flow restrictor to speed up the flow. It is sized for the membrane. Changing it can increase waste or reduce the membrane’s life.

The system keeps running or draining

Constant running usually points to the auto shutoff valve (ASO), which should close when the tank is full. A faulty valve, a leak in the tank, or a tank that has lost pressure can keep the system running and sending water to the drain. Check the tank and the tubing for leaks first, then check the valve.

A failing membrane can also cause long run times, but check the simpler causes first. Our article on how often to replace an RO membrane explains how to measure the membrane’s performance.

For drain water that seems too high for a normal system, see how much water an RO system wastes.

Leaks

Most leaks are simple to fix:

  • Loose fittings. Hand-tighten the fitting. Do not overtighten, because that can crack the fitting or the housing.
  • Damaged O-rings. Inspect the O-ring on each filter housing, and replace it if it is cracked or flattened.
  • Misaligned outlet or spout. On countertop units, check that the outlet points down and that the spout nut is snug.
  • Shipping damage. On a brand-new unit that leaks, a part may have come loose in transit. Check the internal connections, and contact support if you cannot find the cause.

If none of these fixes the leak, turn off the supply and contact support.

Bad taste or odor

Taste and odor changes most often come from an exhausted post-carbon filter. Replace it on schedule. If the taste does not clear, check the storage tank, which can grow bacteria if the system has been idle. Follow the manufacturer’s instructions for sanitizing the tank and the lines. Our post-carbon filter guide explains the stage in more detail.

Unusual noise

A gurgle or hiss can come from air in the lines or from a loose fitting. Check the connections and the tank valve. A loud or new noise, especially from a pump-based system, is worth a call to support, because it can indicate a pump or valve problem.

When to stop using the water and call for service

Stop using the water, and contact the manufacturer or a water professional, if:

  • The water tastes, smells, or looks different in a way you cannot explain.
  • The system leaks near electrical equipment.
  • A water test shows contamination, or you are unsure whether the system is working.

For the broader picture of how an RO system works and what each stage does, see the reverse osmosis pillar guide.

The complete guide to reverse osmosis

Reverse Osmosis Water Treatment: How It Works and Its Pros and Cons
Read the guide

Keep exploring

Guides from other topics

All topics →