Reverse Osmosis

The Sediment Prefilter in an RO System: What It Does and When to Change It

What the sediment prefilter in an RO system catches, how its micron rating matters, when to change it, and the signs that it is clogged.

On this page
  1. Short answer
  2. What the sediment prefilter does
  3. What it does not remove
  4. Micron ratings: 5 or 1
  5. When to change it
  6. Signs it is clogged
  7. Changing it safely
  8. What happens if it is overdue

Short answer

The sediment prefilter is the first stage in most RO systems. It catches sand, silt, rust, and other particles before they reach the carbon stages and the membrane. Change it on the manufacturer’s schedule, which is usually every 6 to 12 months. Change it sooner if your water is sediment-heavy, or if the flow to your storage tank or faucet drops.

What the sediment prefilter does

The filter traps physical particles. Most are made of spun or pleated polypropylene, with a density that captures larger particles on the outside and finer ones inside. By catching particles early, it keeps them away from the carbon stages, which can be clogged, and from the membrane, which can be scratched or blocked.

What it does not remove

The sediment filter does not remove dissolved contaminants, such as salts, most metals, or chemicals. Those are handled by the carbon stages and the membrane. It is also not a disinfection step, so it does not protect against bacteria. For how the stages work together, see the reverse osmosis pillar guide.

Micron ratings: 5 or 1

Sediment filters are rated by the smallest particle size they are designed to catch, measured in microns. The two most common ratings for RO prefilters are 5 microns and 1 micron.

  • A 5-micron filter is the common choice for most residential systems, and it protects the downstream stages well.
  • A 1-micron filter catches finer particles. It can give more protection, but it also tends to clog sooner, especially in sediment-heavy water.

Use the rating your system’s manual specifies. Mixing ratings, or cartridges from different brands, can affect fit and flow.

When to change it

Most manufacturers recommend changing the sediment filter every 6 to 12 months. Use the shorter end of that range if:

  • Your water comes from a private well.
  • Your water has visible sediment, or it looks cloudy or discolored.
  • Your area has recent water main work, which can stir up sediment.

Write the date on the housing or in a note when you change it, so you can keep to the schedule.

Signs it is clogged

  • Water flow to the storage tank or faucet has dropped noticeably.
  • The system takes much longer than usual to fill the tank.
  • When you inspect the used filter, it is discolored, usually brown, yellow, or gray.
  • The water looks cloudy, or you see particles in it.

A drop in flow can also come from other causes, such as low feed pressure or a problem with the shutoff valve. If the sediment filter is current and flow is still low, check those next. Our troubleshooting guide covers them.

Changing it safely

Follow your manual, and keep these points in mind:

  • Turn off the water supply to the RO system, and open the RO faucet to release the pressure.
  • Use the replacement cartridge for your exact model, and do not mix cartridges from different brands.
  • Check the housing O-ring for cracks or wear, and replace it if needed. A light coat of food-grade silicone lubricant helps it seal.
  • Clean the housing with water, and rinse it well if you use soap.
  • After you turn the water back on, check for leaks, and run the faucet until the water runs clear.
  • Do not run hot water through the RO system. Heat can damage the membrane.

Do not clean and reuse a sediment filter. Spun or pleated filters are not designed to be cleaned, and a saturated filter can send particles downstream.

What happens if it is overdue

A clogged sediment filter restricts flow and can force the downstream stages to handle particles they are not designed for. Over time, that can shorten the life of the carbon filters and the membrane. Replacing the sediment filter is one of the lowest-cost steps you can take to protect the rest of the system.

For how the carbon stage works with the sediment filter, see our article on carbon block vs reverse osmosis. For the post-membrane stage, see what the post-carbon filter does. For the membrane itself, see how often to replace an RO membrane.

The complete guide to reverse osmosis

Reverse Osmosis Water Treatment: How It Works and Its Pros and Cons
Read the guide

Keep exploring

Guides from other topics

All topics →