Reverse Osmosis

How Often Should You Replace an RO Membrane?

How often to replace an RO membrane, how prefilters follow a different schedule, the signs of a failing membrane, and how to check its rejection rate with a TDS meter.

On this page
  1. Short answer
  2. How long an RO membrane lasts
  3. Prefilters follow a different schedule
  4. Signs the membrane may need replacing
  5. How to check your rejection rate
  6. Other causes that can look like a bad membrane
  7. When to replace and what to check first

Short answer

Many RO membranes are replaced every few years, and a common range is about 2 to 5 years, depending on your water quality, how well chlorine is removed before the membrane, and how the system is maintained. Prefilters need changing much more often, usually every 6 to 12 months. Do not replace the membrane on a fixed date alone. Check the signs of failure, and rule out other causes first.

How long an RO membrane lasts

The membrane is the part that does the main separation, so its life depends on several things:

  • Feed water quality. Water with high levels of dissolved solids, iron, or scale-forming minerals wears the membrane faster.
  • Chlorine exposure. Most home RO membranes (thin-film composites) are damaged by chlorine. A working carbon prefilter protects them.
  • Water pressure and temperature. Very high pressure or high temperature shortens membrane life.
  • Maintenance. Changing prefilters on time is the most important thing you can do to protect the membrane.

Your system’s manual or the manufacturer’s website gives a recommended interval for your model. Use that figure, and then check the signs below.

Prefilters follow a different schedule

Sediment and carbon prefilters protect the membrane and usually need changing every 6 to 12 months. A prefilter that is overdue can clog, which lowers flow, and it can let chlorine reach the membrane. Changing prefilters on time often extends the membrane’s life. For details, see our article on the sediment prefilter.

Signs the membrane may need replacing

  • Rejection rate has dropped. You can check this with a TDS meter, as described below.
  • Water production has fallen. A system that makes water much more slowly than it used to may have a clogged or failing membrane. Low water pressure can also cause this, so check that first.
  • Taste or smell has changed. Be careful with this sign. A change is often a sign of an exhausted post-carbon filter rather than of the membrane. See our article on the post-carbon filter.

How to check your rejection rate

A TDS meter gives you an approximate reading of the dissolved solids in water. To estimate rejection:

  1. Measure the feed water TDS. Take a sample from the cold-water line that feeds the system, before it reaches the RO unit.
  2. Measure the product water TDS from the RO faucet.
  3. Calculate the rejection rate: (feed TDS minus product TDS) divided by feed TDS, then multiply by 100.

For example, if your feed reads 300 and your product reads 15, the rejection is (300 − 15) ÷ 300 × 100, which is about 95 percent.

TDS meters are approximate, and readings can vary with temperature and calibration. Use the trend over time more than any single reading. Compare your result with the rejection rate in your model’s specifications. Different guides give different replacement thresholds, so the manufacturer’s figure is the one to use.

Other causes that can look like a bad membrane

  • A system that runs constantly, which some guides link to a failing membrane. It can also come from a faulty auto shutoff valve, a leak in the storage tank, or a leak in the line. Check the tank and the fittings before you buy a membrane.
  • Low water production from low feed pressure, a clogged prefilter, or a closed or partly closed inlet valve. Check these first.
  • Slow flow at the faucet from a clogged faucet aerator or restricted tubing, which is simple to check.
  • Taste or odor changes from an exhausted post-carbon filter or a contaminated storage tank.

Our troubleshooting guide covers these checks in order. For the pressure that the system needs, see our article on RO feed pressure.

When to replace and what to check first

Replace the membrane when your readings show that rejection has dropped to your manufacturer’s threshold, and when the simpler causes are ruled out. Before you buy one:

  • Confirm that prefilters are current.
  • Check the feed pressure.
  • Check the tank and the auto shutoff valve.
  • Match the membrane to your model’s exact size and part number.

For the water-quality side, see our article on what TDS level reverse osmosis water should be. For the whole system, see the reverse osmosis pillar guide.

The complete guide to reverse osmosis

Reverse Osmosis Water Treatment: How It Works and Its Pros and Cons
Read the guide

Keep exploring

Guides from other topics

All topics →