Short answer
Most residential reverse osmosis (RO) systems need a minimum feed pressure of about 40 psi and work best below about 80 psi. Check your model’s specification, because the exact range varies. If your home’s pressure is above about 80 psi, a pressure regulator is commonly recommended. If it is well below the minimum, the system will produce water slowly or not at all.
What feed pressure means
Feed pressure is the water pressure entering the RO system. It is your home’s supply pressure, reduced by the pressure drop across the prefilters. A clogged prefilter lowers the pressure that reaches the membrane, even if your home’s supply pressure is fine.
How much pressure an RO system needs
Manufacturers publish a range for each model. Many residential systems list a minimum near 40 psi and a maximum near 80 psi. Some models differ, so use the figure in your manual. The minimum matters most: below it, the membrane does not get enough pressure to push water through efficiently, and the system produces water slowly. The maximum matters for the system’s fittings and housings.
Is 120 psi too high?
Yes, for most residential RO systems, 120 psi is above the range they are designed for. Pressure that high can stress fittings, housings, and tubing, and it can add wear to the system. Many plumbing guides also suggest keeping home water pressure in the 40 to 80 psi range, so a pressure regulator is often the answer, both for the RO system and for the plumbing in the home.
If you measure a high reading, have a plumber check the pressure regulator on the main supply line. Do not try to fix it at the RO unit alone.
How pressure affects osmosis
Osmosis is the natural movement of water across a semipermeable membrane toward the side with more dissolved particles. Osmotic pressure is the pressure needed to stop that movement, and it depends on how concentrated the dissolved particles are. Reverse osmosis reverses the flow by applying pressure greater than the osmotic pressure on the concentrated side.
For typical tap water, which has low levels of dissolved salts, the osmotic pressure is small. The practical limit is the design of the system, not the osmotic pressure itself. Water with more dissolved salts needs more pressure to overcome the osmotic pressure, and this is one reason RO efficiency depends on water quality. For the basics, see osmosis and reverse osmosis.
The storage tank’s pre-charge
Most under-sink systems store treated water in a small tank. The tank has a pre-charge, which is air pressure set when the tank is empty. The pre-charge pushes water out of the tank when you open the faucet.
For a common 4-gallon tank, the pre-charge is often in the range of about 5 to 7 psi when the tank is empty. This figure is specific to the tank, so check the label or the manual. Set it with the tank empty and the water off, using a tire-style gauge on the air valve. A pre-charge that is too low or too high can reduce how much water you get from the tank.
High-pressure switches and auto shutoff valves
Most RO systems use an auto shutoff valve, which closes when the tank is full so that water stops flowing into the membrane. Pump-based systems often use a pressure switch that turns off the pump when the tank reaches a set pressure. Both do the same job: they stop the system from running when the tank is full, which protects the membrane and saves water.
If the system keeps running after the tank is full, check the auto shutoff valve and the tank for leaks. Our troubleshooting guide covers those checks.
Low pressure: causes and fixes
Low feed pressure shows up as slow tank refills and weak output at the faucet. Common causes include:
- Low home supply pressure, which you can measure directly. A whole-house filter upstream can also lower it.
- A clogged prefilter, which is often the easiest fix. Change it on schedule. See our article on the sediment prefilter.
- A closed or partly closed supply valve to the RO system.
- Low tank pre-charge, which affects faucet output more than the membrane.
If your home’s supply pressure is consistently below the system’s minimum, a booster pump may be an option. Choose one that is designed for your RO system, and check your local rules before you install it. Some high-efficiency RO systems need more pressure than standard models, so check the specification before you buy.
How to check your pressure
Use a pressure gauge on a hose bib or a spigot close to the RO system’s supply line, with no water running in the home. Record the static reading. Then open a faucet nearby and see how far the pressure drops. A large drop can point to a supply problem.
Temperature also matters. RO membranes are rated for a range of water temperatures, and very hot water can damage them. Do not run hot water through the system.
For how pressure relates to waste and output, see how much water an RO system wastes. For the broader picture, see the reverse osmosis pillar guide.