Reverse Osmosis

What is the healthiest water filtration system?

There is no single healthiest water filtration system. Learn how to match point-of-use or whole-house stages to your water test, and what to check.

On this page
  1. Start with a water test
  2. Point-of-use or whole-house?
  3. Common stage combinations
  4. Certifications and component materials
  5. Keep the system maintained
  6. A practical default

Short answer: There is no single healthiest water filtration system. The right system addresses the contaminants your water test found, is certified for those contaminants, and is maintained on schedule. For drinking and cooking, a point-of-use system at one faucet covers most needs. A whole-house system makes sense when a problem affects all the water in the home, such as a well with high iron or hardness. Many homes use a combination of stages.

Start with a water test

Choose the system after you know what is in your water. Municipal water comes with an annual Consumer Confidence Report. Private wells are your responsibility to test, and should be tested for bacteria, nitrate, and any contaminants common in your area. A test shows what the system needs to remove, and it stops you from paying for stages you do not need.

Point-of-use or whole-house?

Point-of-use (POU) systems treat water at one faucet, usually the kitchen tap used for drinking and cooking. Examples include under-sink RO units, under-sink carbon filters, countertop units, and pitchers. They cost less to buy and run, and they are the most common choice for drinking water.

Whole-house, or point-of-entry (POE), systems treat all the water that enters the home. They cost more and need professional installation in many cases. They make sense when a problem affects the whole house, such as iron or sulfur that stains fixtures, hardness that damages appliances, or a contaminant that affects showering and laundry as well as drinking. A whole-house system does not replace a drinking-water stage if your water needs more than a carbon filter can provide.

Common stage combinations

Drinking water at one faucet

A typical drinking-water system uses a sediment prefilter, a carbon stage to remove chlorine and taste compounds, and a reverse osmosis membrane for dissolved contaminants. A post-carbon stage polishes the water. Our article on the sediment prefilter explains the first stage.

Whole-house systems

Whole-house systems often use a sediment filter and a granular carbon tank, and sometimes a water softener or a specific media for a particular problem. Each stage is matched to a contaminant, so the combination depends on the water test.

Softeners and sodium

A water softener removes calcium and magnesium by exchanging them with sodium. The result is softened water with more sodium than before. If you are on a low-sodium diet, ask your doctor before drinking softened water. Many people keep a separate, unsoftened drinking tap for this reason.

UV disinfection

UV treatment uses light to inactivate microorganisms, which makes it a tool for microbes rather than chemicals. It needs electricity, and it works only when the water is clear, so it is usually paired with a sediment filter. It does not remove chemicals, dissolved salts, or metals. If your water may contain bacteria, follow local health guidance first, and consider disinfection along with the rest of the system.

Certifications and component materials

Look for certifications that match the contaminants you care about. The common NSF/ANSI standards are 42 for taste and aesthetics, 53 for health contaminants, 58 for RO systems, and 401 for some emerging contaminants. Certification applies to specific models and specific contaminants, so check the listing.

Housing material, such as plastic, metal, or glass, is a matter of preference. Do not treat it as a health measure by itself. If you are concerned about lead in components, look for NSF/ANSI 372 or a similar lead-free certification for the parts that touch the water.

Keep the system maintained

A well-certified system does not protect you if its filters are overdue. Prefilters, carbon stages, and membranes all need replacing on schedule, and a clogged stage can reduce performance across the whole system. Set reminders, and keep spare cartridges on hand if you can. For the membrane, see how often to replace an RO membrane.

A practical default

For most homes, the sensible order is:

  1. Test the water.
  2. Address any contaminant that a test shows, with a certified stage for it.
  3. Use a point-of-use RO or carbon system at the drinking tap if dissolved salts, nitrate, or lead are concerns, or a carbon system if taste and chlorine are the main issues.
  4. Add a whole-house system only when the test shows a problem that affects all the water.

For a single-unit comparison, see the healthiest water filter to use. For how RO fits into a full system, see the reverse osmosis pillar guide. For how total dissolved solids relates to the water you drink, see what TDS level reverse osmosis water should be.

If you are preparing formula, check the water for nitrate and bacteria first, and read our article on RO water and baby formula.

The complete guide to reverse osmosis

Reverse Osmosis Water Treatment: How It Works and Its Pros and Cons
Read the guide

Keep exploring

Guides from other topics

All topics →