Reverse Osmosis

What TDS Level Should Reverse Osmosis Water Be?

What TDS level reverse osmosis water should be, why there is no single ideal number, what the EPA and WHO say, and how to use a TDS meter at home.

On this page
  1. Short answer
  2. What TDS measures
  3. What the guidelines say
  4. What RO water usually reads
  5. Taste and minerals
  6. Why the reading changes
  7. Using a TDS meter
  8. Choosing your target

Short answer

There is no single ideal TDS level for reverse osmosis (RO) water. A working RO system usually produces water with very low total dissolved solids, often in the low tens of parts per million (ppm), though the exact figure depends on your feed water and the membrane. What matters more is whether the reading stays low over time. A rising reading usually means the membrane is losing performance.

What TDS measures

Total dissolved solids (TDS) is the total amount of dissolved material in water, including minerals, salts, and some small organic compounds. It is reported in ppm, which is the same as milligrams per liter (mg/L).

A TDS meter does not weigh the dissolved material. It estimates TDS from how well the water conducts electricity, so the reading is approximate. Temperature affects it, and many meters need calibration.

What the guidelines say

  • EPA: The EPA sets a secondary standard of 500 mg/L for TDS. This is an aesthetic guideline, based on taste and appearance, not a health-based limit.
  • WHO: The World Health Organization has not set a health-based TDS limit. It has noted that very low-mineral water may not be ideal for long-term drinking, mainly because it lacks minerals such as calcium and magnesium that water can contribute. The health significance is debated.

Neither guideline gives a target for RO water. Use them as background, not as a rule for your system.

What RO water usually reads

Feed water varies widely. Municipal water, well water, and surface water can have very different TDS levels, and the same membrane will produce different results depending on the feed. A working membrane typically removes most of the dissolved solids, so the product water reads much lower than the feed.

If your RO water reads close to the feed water’s TDS, the membrane may be failing or the system may be bypassed. Our article on how often to replace an RO membrane explains how to calculate the rejection rate.

Taste and minerals

Taste is personal. Water with very low TDS can taste flat, and many people find that water in a moderate range tastes better. Some people aim for a moderate level by adding minerals back, which is one reason RO water is often remineralized. For the options, see remineralizing RO water.

Sodium is one part of TDS, and softened water carries more of it. If you are on a low-sodium diet, the sodium portion matters more than the total. A water test can show sodium separately, and your doctor can advise you on what matters for your diet.

Why the reading changes

  • Feed water changes. Seasonal changes, well water conditions, and municipal treatment can all change the feed TDS, and the product reading changes with it.
  • Membrane age. A membrane that is losing performance lets more dissolved solids through.
  • Pressure and temperature. Low feed pressure or cold water reduces performance, which can raise the product reading.
  • Prefilter or post-filter problems. A clogged prefilter reduces pressure, and a worn post-carbon filter does not change TDS much, but it does affect taste.

A single reading is less useful than a series of readings. Record them over time and compare them with the same feed water.

Using a TDS meter

  • Measure both sides. Test the cold feed water before the RO system, and test the RO faucet water. Use the same method and the same temperature range for both.
  • Calibrate the meter if the manufacturer says to, and keep it dry and clean.
  • Use the trend. Look for a steady rise in the product reading. That is more useful than a single number.
  • Know what it cannot tell you. A TDS meter does not detect lead, PFAS, bacteria, or pesticides. It shows only the overall level of dissolved material. Use a certified test for specific contaminants.
  • Do not chase a number. A reading that is very low is not a problem by itself, and a reading that is moderate is not a problem if it is stable and tastes right.

Choosing your target

Start by asking what you want the water to do. If you want the purest water possible, RO does that. If taste or minerals are the concern, a remineralization stage can adjust the result, and our guide to adding minerals to RO water naturally covers the options.

For the difference between RO and distilled water, which are both very low in dissolved solids, see reverse osmosis vs distilled water. For how pH relates to very low-mineral water, see whether RO water is acidic. For the overall picture, see the reverse osmosis pillar guide.

The complete guide to reverse osmosis

Reverse Osmosis Water Treatment: How It Works and Its Pros and Cons
Read the guide

Keep exploring

Guides from other topics

All topics →